Nissan Navara NP300 (D23) DIY

**pjcunom** · January 19th, 2018 06:44 PM

Hi mga sir, post natin dito mga DIY natin sa navara. Share knowledge po.. Thanks

Sent from my XT1650 using Tapatalk

**godwhacker** · January 21st, 2019 06:03 PM

Originally Posted by pjcunom

Hi mga sir, post natin dito mga DIY natin sa navara. Share knowledge po.. Thanks

Sent from my XT1650 using Tapatalk

I updraded my factory reverse camera to a higher definition after market -Sinairyu
and installation is here...

NISSAN NAVARA NP3 factory reverse camera upgrade - Album on Imgur

**godwhacker** · February 22nd, 2019 02:56 PM

my LED Tail light upgrade

remove the tail lights with two 10mm bolts. lift the original tail light carefully with a plastic prying tool and hold it firmly.

there are 6 wires on the connector

connect and solder the 6ohm load resistor (i made it from two 12ohm 10W ceramic resistors connected, soldered in parallel and insulated the connections with a ceramic sealant) to the signal lights wires and insulate with electrical tape. 6 ohms is required to retain the normal flash rate. no load resistor, flash rate is faster.

test the LED lights before final installation.

finally, install the new LED tail light assembly

i have more pics at imgur. photos here are limited by moderator.

**godwhacker** · February 24th, 2019 11:25 PM

also added THe V5 NAVARA grille..

Navara logo changes color between white/amber when turning lights/applying brakes. patong lang and i didn't get rid of the original grille in case mag sawa. connection of the controller wires took some time.
at side view, bumukol mukha ng navara!

i'll be back with the ADAS rear view mirror upgrade and the 3D 360deg AVM add on when it comes.

**12vdc** · February 25th, 2019 12:03 AM

I don't D23 but i do D40, somebody could confirm if tailgate damper install is worthit-no frills plug-in install?

I bet we have the same heavy tailgate that needs dampening, atleast the D23 is now lockable.

Concorde SUS.TEC Easy Down Tailgate Damper Navara 26-215 (1 Pc) | Lazada PH

**Wh1stl3r** · February 25th, 2019 09:38 AM

Originally Posted by 12vdc

I don't D23 but i do D40, somebody could confirm if tailgate damper install is worthit-no frills plug-in install?

I bet we have the same heavy tailgate that needs dampening, atleast the D23 is now lockable.

Concorde SUS.TEC Easy Down Tailgate Damper Navara 26-215 (1 Pc) | Lazada PH

At the dealer I noticed the D23's is quite a bit lighter bro. The hood seems heavier though. Might want to install dampers at the front end as well.

**nelyoung** · November 26th, 2019 02:00 AM

Originally Posted by godwhacker

my LED Tail light upgrade

remove the tail lights with two 10mm bolts. lift the original tail light carefully with a plastic prying tool and hold it firmly.

there are 6 wires on the connector

connect and solder the 6ohm load resistor (i made it from two 12ohm 10W ceramic resistors connected, soldered in parallel and insulated the connections with a ceramic sealant) to the signal lights wires and insulate with electrical tape. 6 ohms is required to retain the normal flash rate. no load resistor, flash rate is faster.

test the LED lights before final installation.

finally, install the new LED tail light assembly

i have more pics at imgur. photos here are limited by moderator.

Good job bro! very informative. will follow the steps. hehe