isuzu hilander owners

[ronball]

Mga Sir,

ask ko lang sana kung may kinalaman ba ang oil cooler sa paghalo ng water sa oil..kasi po nauubos ung tubig sa radiator at tumataas ang langis sa dipstick tapos kulay gray sya...

Kasi ang sabi ng dating mekaniko, pag oil cooler dw ung radiator and mapupuno ng lan
gis..pero sa case ng car ko ,,,nsa langis ang water...bagong overhaul din ung radiator ko kaya walang leak..

SAAN PO KAYA ANG PROBLEM MGA SIR? PLEASE HELP ME......

*sniper10,

ito'y personal na assumption lamang na pwede mong iconsider.

May duda ako na somewhere along your engine block na iniikutan ng tubig ay may crack na at doon dumadaan ung tubig papsok sa engine mo. Pwede ka bumili sa ebay ng smoke machine. I-pressurize mo ng smoke ung engine mo at tinggnan nyo kung saan lalabas ung usok that way, mas madali ang tracing (aking suggestion lang yan)

BTW, kumatok na ba makina mo? maaari kasi may part na ng pinagpapatungan ng head gasket mo ang bingkong na at kahit anong lapat ng gasket ay nalulusutan pa din sya ng tubig

Sinilip na ba ng mekaniko ung thermostat housing? di pa ba corroded

Sinilip na ba ng mekaniko ung timing gear cover? wala bang crack?

[ronball]

Regarding sa dipstick, lagyan mo lang ng wire na mag prevent pushing up para malimit talsik, ganun na din yung sa akin. Malakas na blowby, so ginawa ko, naka disconnect na crankcase breather hose going to intake palabas, nilagyan ko na lang ng homemade oil catch can then chemical hose patungong airfilter. Sinarado ko ma din yung pinagkonekan na tubo bandang intake. This way maiwasan kung iconsume ng makina sariling engine oil nya. Medyo oily nga lang air filter ko dahil may oil moist dun sa usok due from crankcase.

Sent from a mobile device.

*aioshin,
Right now paps am not keen in altering the original architecture of the 4JA1's ventilation system. What I want is to replace the PCV valve. But your suggestion is highly noted sir.

Have you replaced your PCV valve before?

[aioshin]

*aioshin,
Right now paps am not keen in altering the original architecture of the 4JA1's ventilation system. What I want is to replace the PCV valve. But your suggestion is highly noted sir.

Have you replaced your PCV valve before?

Honeslty, am not sure if there is a PCV Valve for our hilander. There is a hose though, the one from your crankcase going to your intake and its a breather hose.

[ronball]

Honeslty, am not sure if there is a PCV Valve for our hilander. There is a hose though, the one from your crankcase going to your intake and its a breather hose.

*aioshin,

nung kausap ko ung salesman ng jetco ang tawag nila sa sa PCV valve is ventilation diaphragm, while dun sa Isuzu online manual na nabasa ko is PCV valve talaga ang term nila. Sa isa namang online spare parts seller sa Hongkong ang term nila is Crankcase (cylinder head cover) Ventilation Valve na para sakin is iisa lang ung tinutukoy nung mga iba-ibang description na yun at yun na nga ung PCV valve. Di lang kasi pwede mag-upload ng picture dito directly eh, kaya di ko maipakita. I have also read na isa itong part ng ventilation system na always being taken for granted or madalas pinapabayaan lang at hindi pinapalitan.

So after owning this 2nd hand Hilander for 7+ years eh ngayon ko pa lang talaga mapapalitan ung PCV valve nya. I'll post an update if everything goes well or not. Kung di na ba mapu-push upward ang dipstick ko at mababawasan or totally mawawala na ung tilamsik ng oil sa dipstick

[danny@briellaga]

sali dn ako mga kaibigan.mgtatanong lng ako..kung meron nb nkasubok mg convert ng 4ja1 hilander xtrm.lalagyan ng intercooler turbo.mgknu inabot ng parts and labor.balak ko kc iturbo un sken..model 2001.

share ko lng dn gnwa ko sa xtrm ko about wheel bearing..so far wala ng ko nging problem sa front wheel ko.pnare-thread (roughthread)ko spindle sa machineshop.kc nun nbasag bearing kinain un lock nut ng spindle hnggang nloosethread na.lumabas n gulong buti my brake caliper,hnd tuluyan bumitaw ung gulong at mbagal lng takbo.after re-thread.centro n uli ikot ng bearing but still lage p dn kumakalog kht sobrng adjust na.cnbhan ako ng friend ko n mechanic.lagyan dw ng manipis ng spacer(washer) ung inner bearing..pra maitulak ung bearing palapit sa hub..ginawa ko nmn..so far nkakadalawang balik n sa cagayan province from manila walang adjust adjust kht loaded..monitor lng condition.tipid pa dn kht blowby na.hehehe.roundtrip cagayan-manila P2500 via ilocos

Sent from my A33w using Tsikot Forums mobile app

[cjgambit]

Changed Oil for my ride today :D

Castrol CRB turbo 4L * 900 Ace Hardware
Air filter/cleaner * 200 suking autoshop
Fuel filter (FC-208A) * 240 suking autoshop
Oil filter (C-512) * 220 suking autoshop
Change Oil labor * 250 suking gasolinahan

next front suspension repairs may konting wiggle sa isang side eh. mukhang may papalitan akong tie rod (atleast un).

[XanderU]

Mga boss ghost town na po ata itong HiLander thread. Pero magbabaka sakali parin po ako baka may makakatulong. Talaga po bang mahirap isara ang mga HiLander na unit dahil medyo nakaka bingi na lalo na at sarado lahat ng bintana hahaha. Meron po bang solution or nature na po talaga ng mga sasakyang halos 20yrs old and up ito? Salamat po sa makakasagot, nagbabaka sakali po na may ibang na paraan maliban sa pagpapapalit ng pinto mismo or lock mechanism dahil ang hirap po talagang humanap ng katay ng HiLander sa totoo lang. Maraming salamat po.

[Archerfish]

Mga boss ghost town na po ata itong HiLander thread. Pero magbabaka sakali parin po ako baka may makakatulong. Talaga po bang mahirap isara ang mga HiLander na unit dahil medyo nakaka bingi na lalo na at sarado lahat ng bintana hahaha. Meron po bang solution or nature na po talaga ng mga sasakyang halos 20yrs old and up ito? Salamat po sa makakasagot, nagbabaka sakali po na may ibang na paraan maliban sa pagpapapalit ng pinto mismo or lock mechanism dahil ang hirap po talagang humanap ng katay ng HiLander sa totoo lang. Maraming salamat po.

I think this is normal, basing from our previous hilander. There was a time that water would drip around the door. I even "lost" my steering​ wheel! Good thing I was in a very busy street so I wasn't driving fast. And of all places for an ambulance being towed, the rope severed just besides me! Imagine the traffic jam that caused it.

... nature na po talaga ng mga sasakyang halos 20yrs old and up ito?

I don't think so. Our CR-V 98 is 20 years old and still runs fine. It might be that the vehicle was subjected to abuse beyond its normal design. In our case, the hilander was used as a utility/delivery vehicle and no specific driver was assigned to take care of it.

Regarding your concern about alternative solution to your door, I believed that you are correct that there is no other solution to it except to what you have said. There is the possibility that the door is no longer aligned.

[XanderU]

I think this is normal, basing from our previous hilander. There was a time that water would drip around the door. I even "lost" my steering​ wheel! Good thing I was in a very busy street so I wasn't driving fast. And of all places for an ambulance being towed, the rope severed just besides me! Imagine the traffic jam that caused it.



I don't think so. Our CR-V 98 is 20 years old and still runs fine. It might be that the vehicle was subjected to abuse beyond its normal design. In our case, the hilander was used as a utility/delivery vehicle and no specific driver was assigned to take care of it.

Ok boss maraming salamat po sa reply, as far as performance goes wala pong problema. Actually napakaganda po ng performance ng hilander namin tested sa long drive at matipid sa konsumo kahit naka aircon pa (modified na yung aircon sa likod). Problema ko lang po talaga ay yung mga pinto dahil kailangan "with feelings" ang pagsasara. Mukang dapat ay humanap na ako ng kinakatay na hilander at mag dasal na maayos pa ang mga door, window at lock mechanism nila.

[XanderU]

I think this is normal, basing from our previous hilander. There was a time that water would drip around the door. I even "lost" my steering​ wheel! Good thing I was in a very busy street so I wasn't driving fast. And of all places for an ambulance being towed, the rope severed just besides me! Imagine the traffic jam that caused it.



I don't think so. Our CR-V 98 is 20 years old and still runs fine. It might be that the vehicle was subjected to abuse beyond its normal design. In our case, the hilander was used as a utility/delivery vehicle and no specific driver was assigned to take care of it.

Regarding your concern about alternative solution to your door, I believed that you are correct that there is no other solution to it except to what you have said. There is the possibility that the door is no longer aligned.

Salamat sa reply boss, pero as far as performance goes wala ako reklamo sa unit namin. Yung pinto lang talaga at mga window raiser . Balak ko na nga i-perma shut yung mga bintana kaya lang sa init ngayon at sa pagtitipid kailangan talaga mag baba ng bintana. Nag papractice parin kasi ako dahil bago lang akong nag da-drive. Ok naman sa highway kaso medyo bulok pa sa parking at reverse. Wala pambayad sa driving school kaya turo turo lang .

[digitel]

well.. i have a 1998 isuzu hi-lander SL, still a good looking car..do dents and scratches..Thank God!

Nice one sir! Post a picture of your good looking hi lander!

[S.L.X.]

well.. i have a 1998 isuzu hi-lander SL, still a good looking car..do dents and scratches..Thank God!

taga cebu ka pala sir???

join us on facebook http://www.facebook.com/group.php?gi...&v=info&ref=ts

http://clubisuzuphils.tk/